Torque imporvement of IPM motors with skewing magnetic designs
278 viewsDOI:
https://doi.org/10.54939/1859-1043.j.mst.76.2021.3-10Keywords:
Interior Permanent Magnet; Torque, V shape, Skewing design.Abstract
In this paper, a type interior permanent magnet synchronous motor designs is proposed for sport scooter application to improve constant torque wide speed performance. Interior Permanent Magnet machines are widely used in automotive applications for their wide-speed range operation and low maintenance cost. An existing permanent magnet motor (commercial QS Motor) is 3 kW-3000 rpm. In order to improve torque and power in wide speed range, a IPM electric motor 5.5 kW -5000 rpm can run up to 100 km/h: An Step-Skewing Interior Permanent Magnet motor alternatives is designed and optimized in detail with optimal magnetic segment V shape. The electromagnetic charateristics of Interior Permanent Magnet motors with V shape are compared with the reference Surface Permanent Magnet motor for the same geometry parameter requirements. Detailed loss and efficiency result is also analyzed at rate and maximum speeds. A prototype motor is manufactured, and initial experimental tests are performed. Detailed comparison between Finite Element Analysis and test data are also presented. It is shown that it is possible to have an optimized Interior Permanent Magnet motor for such high-speed traction application. This paper will figure out optimal angle of magnetic V shape for maximum torque and minimum torque ripple.
References
[1]. Yunpeng Si; Yifu Liu; Chunhui Liu; Zhengda Zhang; Mengzhi Wang; Qin Lei, “A Constant Current Based Interior Permanent Magnet (IPM) Synchronous Motor Drive Control Strategy”, IEEE Energy Conversion Congress and Exposition, INSPEC Accession Number. 20135262 (2020), pp. 2641-2648.
[2]. Junqiang Zheng; Wenxiang Zhao; Christopher H. T. Lee;Jinghua Ji;Gaohong Xu, “Improvement torque performances of interior permanent-magnet machines”, CES Transactions on Electrical Machines and Systems, Volume. 3, Issue. 1(2019), pp.12-18.
[3]. Jonas Bruckschlögl; Johannes Germishuizen; Andreas Kremser, “Design optimisation of IPM machines considering the constant power range”, 19th International Symposium on Electromagnetic Fields in Mechatronics, Electrical and Electronic Engineering, INSPEC Accession Number. 19632550 (2019).
[4]. Q. Chu and Z. Q. Zhu, “Reduction of On-Load Torque Ripples in Permanent Magnet Synchronous Machines by Improved Skewing,” IEEE Trans. On Magnetics, vol. 49, no.7 (2013), pp. 3822- 3825.
[5]. T. Li and G. Slemon, “Reduction of Cogging Torque in Permanent Magnet Motors,” IEEE Trans. On Magnetics, vol. 24, no.6 (2013), pp. 2901-2903, Jul.
[6]. X. Ge, Z. Q. Zhu, G. Kemp, D. Moule and C. Williams, “Optimal step-Skew Methods for Cogging Torque Reduction Accounting for Three-Dimensional Effect of Interior Permanent Magnet Machines,” IEEE Trans. On Energy Conversion, vol. 32, no. 1 (2017), pp. 222-232.
[7]. J. Urresty, J. Riba, L. Romeral and A. Garcia, “A Simple 2-D FiniteElement Geometry for Analyzing Surface-Mounted Synchronous Machines With Skew Rotor Magnets,” IEEE Trans. On Magnetics, vol. 46, no.11 (2010), pp. 3948-3954.
[8]. R. Islam, I. Husain, A. Fardoun and K. McLaughlin, “Permanent Magnet Synchronous Motor Magnet Designs With Skewing for Torque Ripple and Cogging Torque Reduction,” IEEE Trans. Ind. Appl., vol. 45, no. 1 (2009), pp. 152-160.
