Optimization according to strength of thermo-mechanical process combined with aging of B95 aluminum alloy using Taguchi experimental planning method
145 viewsDOI:
https://doi.org/10.54939/1859-1043.j.mst.86.2023.151-157Keywords:
B95, themomechanical, aging, Taguchi method.Abstract
The structure and mechanical characteristics of heat-treated deformable aluminum alloys are significantly impacted by the thermo-mechanical process. In this study, a number of 9 specimens with different rolling ratio, aging time and aging temparature were conducted to experimentally investigated the microstructures and mechanical properties. Beside, the Taguchi method is applied to optimize the themomechanical and aging parameters of the process at which the allloys achieved the highest tensile strength. The findings demonstrate that the obtained highest tensile strength for alloy was 580 MPa at the hot rolling deformation of 70%, aging temperature 150 °C, and the 10-hour aging time.
References
[1]. E.A. Starke Jr, J.T. Staley, “Application of modern aluminum alloys to aircraft”, Progress in Aerospace Sciences, Vol. 32, pp. 131 – 172, (1996). DOI: https://doi.org/10.1016/0376-0421(95)00004-6
[2]. Phùng Tuấn Anh, “Nhôm và hợp kim nhôm” - Nhà xuất bản khoa học và kỹ thuật, (2015).
[3]. Nghiêm Hùng, “Kim loại học và nhiệt luyện” - Nhà xuất bản đại học và trung học chuyên nghiệp và kỹ thuật, (1979).
[4]. D. Ortiz, M. Abdelshehid, R. Dalton, J. Soltero, R. Clark, M. Hahn, E. Lee, W. Lightell, B. Pregger, J. Ogren, P. Stoyanov, O.S. Es-Said, “Effect of Cold Work on the Tensile Properties of 6061, 2024, and 7075 Al Alloys”, Journal of Materials Engineering and Performance, Vol. 16, pp. 515 - 520 (2007). DOI: https://doi.org/10.1007/s11665-007-9074-7
[5]. Hamilton, C. and A. Ghosh, “Superplastic sheet forming, ASM Handbook”, Vol. 14B, (1988).
[6]. Wangtu Huo, “Improved thermo-mechanical processing for effective grain refinement”, Materials Science & Engineering A, Vol. 626, pp. 86 – 93, (2014). DOI: https://doi.org/10.1016/j.msea.2014.12.071
[7]. Wangtu Huo, “An improved thermo-mechanical treatment of high-strength Al-Zn-Mg-Cu alloy for effective grain refinement and ductility RI-ITMT”, Journal of Materials Processing Technology, Vol. 239, pp. 304 - 314, (2017). DOI: https://doi.org/10.1016/j.jmatprotec.2016.08.027
[8]. Shyam Kumar Karna, Dr. Ran Vijay Singh, Dr. Rajeshwar Sahai, “Application of Taguchi Method in Indian Industry”, International Journal of Emerging Technology and Advanced Engineering, Vol. 2, issue 11, (2012).
[9]. Saran Raj, S. Garesan “Process parameter analysis of deep cryogenic treated EN 52 Silicon chromium valve steel through Taguchi technique”, Materials and Manufacturing Processes, Vol.37, Issue 16, (2022). DOI: https://doi.org/10.1080/10426914.2022.2065003
[10]. Senthil, T. Selvaraj and S. Vinodh, “Modelling of turning parameters of Al-Cu/TiB2 insitu metal matrix composites using artificial neural network”, International Journal of Advanced Operations Management, Vol. 4, No. 4, (2012). DOI: https://doi.org/10.1504/IJAOM.2012.049913
